If you have been reading about stationary phase and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Updated 2026-07-24. Numbers and descriptions here follow the published literature rather than marketing material.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
| Property | Value | Notes |
|---|---|---|
| Accuracy | Closeness to true value | Often assessed by recovery of spiked samples |
| Precision | Agreement among repeated measurements | Often reported as relative standard deviation |
| Specificity | Ability to measure analyte without interference | Must separate analyte from impurities and matrix |
| Linearity | Proportional detector response | Evaluated across a defined concentration range |
| Robustness | Resistance to small method changes | Tests flow rate, pH, temperature, and mobile phase composition |
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
MT-ND6 interacts with the NADH dehydrogenase [ubiquinone] iron-sulfur protein 3 (NDUFS3) and the ATP-dependent metalloprotease YME1L1. Mass spectrometry characterization of MT-ND6 at COPaKB GeneReviews/NCBI/NIH/UW entry on Mitochondrial DNA-Associated Leigh Syndrome and NARP This article incorporates text from the United States National Library of Medicine, which is in the public domain.
3-M syndrome or 3M3 is a rare hereditary disorder characterized by severe growth retardation, facial dysmorphia, and skeletal abnormalities. The name 3-M is derived from the initials of the three researchers who first identified it: Miller, McKusick, and Malvaux; they reported their findings in the medical literature in 1972. Mutations in any one of the following three genes: CUL7, OBSL1, and CCDC8 are responsible for the occurrence of this disorder. It is inherited through an autosomal recessive pattern and considered very rare, so far less than 100 cases worldwide have been identified. Diagnosis is based on the presence of clinical features. Genetic testing can confirm the diagnosis and identify the specific gene involved. Treatment is aimed at addressing the growth and skeletal problems and may include surgical bone lengthening, adaptive aids, and physical therapy. An endocrinologist may assist with growth hormone replacement and appropriate evaluations during puberty.
the cAMP signal pathway and the phosphatidylinositol signal pathway. When a ligand binds to the GPCR it causes a conformational change in the GPCR, which allows it to act as a guanine nucleotide exchange factor (GEF). The GPCR can then activate an associated G protein by exchanging the GDP bound to the G protein for a GTP. The G protein's α subunit, together with the bound GTP, can then dissociate from the β and γ subunits to further affect intracellular signaling proteins or target functional proteins directly depending on the α subunit type (Gαs, Gαi/o, Gαq/11, Gα12/13). GPCRs are an important drug target, and approximately 34% of all Food and Drug Administration (FDA) approved drugs target 108 members of this family. The global sales volume for these drugs is estimated to be 180 billion US dollars as of 2018. It is estimated that GPCRs are targets for about 50% of drugs currently on the market, mainly due to their involvement in signaling pathways related to many diseases i.e. mental, metabolic including endocrinological disorders, immunological including viral infections, cardiovascular, inflammatory, senses disorders, and cancer. The long ago discovered association between GPCRs and many endogenous and exogenous substances, resulting in e.g. analgesia, is another dynamically developing field of the pharmaceutical research.
Sources: en.wikipedia.org
The frog Xenopus laevis serves as an ideal model system for the study of the mechanisms of apoptosis. In fact, iodine and thyroxine also stimulate the spectacular apoptosis of the cells of the larval gills, tail and fins in amphibian's metamorphosis, and stimulate the evolution of their nervous system transforming the aquatic, vegetarian tadpole into the terrestrial, carnivorous frog. Negative regulation of apoptosis inhibits cell death signaling pathways, helping tumors to evade cell death and developing drug resistance. The ratio between anti-apoptotic (Bcl-2) and pro-apoptotic (Bax) proteins determines whether a cell lives or dies. Many families of proteins act as negative regulators categorized into either antiapoptotic factors, such as IAPs and Bcl-2 proteins or prosurvival factors like cFLIP, BNIP3, FADD, Akt, and NF-κB.
S-Arrestin is a protein found in mice that binds to rhodopsin to stop its activity, preventing further signaling. S-arrestin binds to G protein-coupled receptors (GPCRs), like rhodopsin, following receptor activation and phosphorylation by G protein-coupled receptor kinases (GRKs). Rhodopsin is found in rod cells of the retina, essential for vision. It detects light and initiates a signaling cascade called phototransduction. However, excessive activation can be harmful, so it must be carefully regulated. The phosphorylation of the receptor's intracellular loops and C-terminal tail creates a high-affinity binding site for S-arrestin. S-arrestin then sterically hinders further G protein coupling, effectively desensitizing the receptor and directing it towards alternative signaling pathways or internalization via clathrin-mediated endocytosis.
The Bergmann degradation is a series of chemical reactions designed to remove a single amino acid from the carboxylic acid (C-terminal) end of a peptide. First demonstrated by Max Bergmann in 1934, it is a rarely used method for sequencing peptides. The later developed Edman degradation is an improvement upon the Bergmann degradation, instead cleaving the N-terminal amino acid of peptides to produce a hydantoin containing the desired amino acid. The Bergmann degradation follows the earlier work of Bergmann and his close colleague Leonidas Zervas, combining the organic azide degradation of the Curtius rearrangement with the Bergmann-Zervas carbobenzoxy method, which they designed to occur under relatively mild conditions so as to allow peptide sequencing. A single round of the Bergmann degradation yields an aldehyde containing the sought after amino acid residue and the remaining fragment of the original peptide in amide form.
Sources: en.wikipedia.org
A nuclide is a more general term than isotope, and refers to atoms that have any particular number of protons and neutrons. Stable nuclides are not radioactive and do not spontaneously undergo radioactive decay, so are more usually found in nature. Whereas unstable (i.e. radioactive) nuclides are not found in nature, unless there is a recent source of them, because they are shorter lived, and will spontaneously decay, in one or more steps, to more stable nuclides. For example, carbon-14 is unstable but is found in nature. Scientists use accelerators and nuclear reactors to produce radioactive nuclides. As a general trend, and among other factors, the neutron–proton ratio of a nuclide determines its stability. The value of this ratio for stable nuclides generally increases for larger nuclei with more protons and neutrons. Many unstable nuclides have neutron-proton ratios beyond the zone of stability. The time required to lose half of a quantity of a given nuclide through radioactive decays, the half-life, is a measure of how stable an isotope is. Nuclides can be visually represented on a table (Segré chart or table of nuclides) where the proton number is plotted against the neutron number.
Tuberculin, known in its modern form as purified protein derivative (PPD), is a combination of proteins that are used in the diagnosis of tuberculosis by injection into the skin. Common side effects include redness, itchiness (pruritus), and pain at the site of injection. Allergic reactions may occasionally occur. Use is safe in pregnancy. The original tuberculin, a glycerin extract of Mycobacterium tuberculosis, was discovered in 1890 by Robert Koch. Koch, best known for his work on the etiology (cause, origin) of tuberculosis (TB), laid down various rigorous guidelines that aided the establishment between a pathogen and the specific disease that followed that were later named Koch's postulates. Although he initially believed it would cure tuberculosis, this was later disproved. PPD was invented in 1934 by Florence B. Seibert, greatly improving the reliability of the skin test over Koch's extract. PPD is on the World Health Organization's List of Essential Medicines.
Albert Pinhasov (Hebrew: אלברט פנחסוב; born 9 February 1972) is the Rector of Ariel University. He is a researcher in the fields of Molecular Psychiatry and Psychopharmacology.He also served as Vice President and Dean for Research & Development and the Head of the Department of Molecular Biology at Ariel University. Albert Pinhasov was born on 9 February 1972 in the city of Namangan, Uzbekistan. From 1990 to 1994, he studied at the Gorky Academy of Medicine, in the city of Nizhny Novgorod, Russia. In 1994, he immigrated to Israel where he continued his education at Tel Aviv University. He was awarded a Master of Science degree (MSc) in 1998 and a PhD in the field of Molecular Biology and Clinical Biochemistry under the mentorship of Illana Gozes in 2002 from Tel Aviv University.
Sources: en.wikipedia.org
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.
Validation demonstrates that a method produces reliable results for a defined purpose. It documents performance limits and acceptance criteria. Regulated industries require validation before routine testing of products or samples.
Retention time shifts can arise from changes in mobile phase composition, pH, temperature, column age, or flow rate. Contamination or worn seals may also alter pressure and delivery. Systematic checks of these factors help identify the cause.
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.